Scottie's Zuke. Blue

Got an vehicle build underway? post up pictures and tell us all how its going!

Builds threads only please.
Post Reply
User avatar
Tramp
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2828
Joined: Fri Jul 25, 2008 10:09 pm
Location: Rotherham - South Yorkshire

Re: Scottie's Zuke

Post by Tramp » Wed Aug 21, 2013 1:35 pm

Oh well it was an idea, I suppose if its over 32mm of positive offset you couldn't even run spacers with the reversed rim to correct it. I've heard of people cutting out the centre of rims and welding them back in to give a better offset, could you do the same except reduce the offset on the rear wheels?if its 3" wider on the rear you would only have to move the rim centres 1.5" towards the middle (on each wheel) to reduce the offset and get it back lined up with the front wheel track,
Top
User avatar
ScottieJ
The Boss
The Boss
Posts: 11620
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: Scottie's Zuke

Post by ScottieJ » Wed Aug 21, 2013 2:55 pm

Tramp wrote:Oh well it was an idea, I suppose if its over 32mm of positive offset you couldn't even run spacers with the reversed rim to correct it. I've heard of people cutting out the centre of rims and welding them back in to give a better offset, could you do the same except reduce the offset on the rear wheels?if its 3" wider on the rear you would only have to move the rim centres 1.5" towards the middle (on each wheel) to reduce the offset and get it back lined up with the front wheel track,

I don;t wan to cut up these wheels ;) When I swap to the GV steels that are noaarower with less offset I'll just run some wheel spacers up front to even it out :thumbup:
Zuki Build

Steady as she goes!
Top
User avatar
ScottieJ
The Boss
The Boss
Posts: 11620
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: Scottie's Zuke

Post by ScottieJ » Sun Sep 22, 2013 5:38 pm

:bawling: had quite a catastrophic headgasket failure at 3am this morning after a night laning session, luckily it was only about a 5mile drive on 2 cylinders for the rest of the journey home.

Seems to have blown between 2&3 as my compression results are 160-0-0-120 :hahaha:

Head off next weekend for inspection and rebuild.
Zuki Build

Steady as she goes!
Top
User avatar
dan_2k_uk
I spend far too much time on here
I spend far too much time on here
Posts: 4924
Joined: Tue May 06, 2008 5:19 pm
Location: Swindon, Wiltshire

Re: Scottie's Zuke

Post by dan_2k_uk » Sun Sep 22, 2013 6:13 pm

I made it home OK :thefinger:
Image
Janspeed manifold, LWB Vit vented discs and calipers

Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Top
User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4555
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: Scottie's Zuke

Post by ROBBIE » Sun Sep 22, 2013 6:43 pm

:hahaha: Dan that's not nice
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Top
User avatar
ScottieJ
The Boss
The Boss
Posts: 11620
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: Scottie's Zuke

Post by ScottieJ » Sun Sep 22, 2013 7:05 pm

dan_2k_uk wrote:I made it home OK :thefinger:
Dick :thefinger: ..........So did I...........on 2 cylinders :hahaha: then drove it to the workshop today ready for the strip down.
Zuki Build

Steady as she goes!
Top
User avatar
NylonAdmiral
Winching along now
Winching along now
Posts: 521
Joined: Wed Apr 03, 2013 8:39 pm
Location: Devizes, Wiltshire
Contact:
Contact NylonAdmiral

Re: Scottie's Zuke

Post by NylonAdmiral » Sun Sep 22, 2013 7:26 pm

OneDoesNot.JPG
OneDoesNot.JPG (29.61 KiB) Viewed 6443 times
1.6 16v, Rock Lobster, PAS, Muddyzook rear disc conversion, coated in Raptor, 33in x 10.5, heated seats, lovingly restored by Scottie!
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Scottie's Zuke

Post by Jordi » Sun Sep 22, 2013 7:55 pm

Sounds like fun.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
Edweird
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2531
Joined: Sat Jan 23, 2010 11:04 pm
Location: Brigg, North Lincolnshire

Re: Scottie's Zuke

Post by Edweird » Sun Sep 22, 2013 8:26 pm

NylonAdmiral wrote:
OneDoesNot.JPG
No matter how minor or trivial, something always gets broken.
There's three ways of doing things:

The right way,
The wrong way
And my way, which is like the wrong way but faster.
Top
User avatar
TanZuk
Engaged 4wd low
Engaged 4wd low
Posts: 234
Joined: Thu Jan 05, 2012 11:17 pm
Location: Pompano Beach, Florida US

Re: Scottie's Zuke

Post by TanZuk » Sun Sep 22, 2013 9:32 pm

ScottieJ wrote::bawling: had quite a catastrophic headgasket failure at 3am this morning after a night laning session, luckily it was only about a 5mile drive on 2 cylinders for the rest of the journey home.

Seems to have blown between 2&3 as my compression results are 160-0-0-120 :hahaha:

Head off next weekend for inspection and rebuild.

Scott, That really stinks. Hate to hear things like that.

My DD usually has some issue about once a month on the way over to the shop. I end up limping into the shop and fix it and start back on the build the next day. Got to say it has only left me stranded 2 times. Dead battery at the grocery store and a clutch cable busted the liner out and had to get it towed to the shop that time.

The 2 and 3 cylinders is usually where the head gasket fails for some reason. The last head gasket I used was a good quality sandwhich type from Altron if that helps. You will probably have to have the head miiled to fix it. It is a good idea to re-torque the head after a few day just for to be sure it is seated.

I Know that you will have it up and running in no time.

Terry
Top
Post Reply

Return to “Builds and Projects”