ruf help :(

Post your questions about your suspension and steering problems here!
Post Reply
User avatar
hamer
Engaged 4wd low
Engaged 4wd low
Posts: 159
Joined: Mon Jul 23, 2012 8:06 pm
Location: bridgend

ruf help :(

Post by hamer » Fri Feb 08, 2013 6:21 pm

Hi guys
i cant get the front shackles to sit right
have i welded them forward enof?
anyone got a pick i can have look of(side view)
thanks
richy
Attachments
2013-02-08 18.11.07.jpg
2013-02-08 18.11.07.jpg (1.43 MiB) Viewed 6593 times

User avatar
ScottieJ
The Boss
The Boss
Posts: 11618
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: ruf help :(

Post by ScottieJ » Fri Feb 08, 2013 6:30 pm

Could probably do with going a little bit further forward or you could just run a slightly longer shackle as that will reduce the angle, you're about on the limit of what you can get away with, without risking flipping the shackle under compression, with an angle like that you will actually maximise the amount of droop you will get.

Are you intending on bracing that mount? It does need to be gusseted as it looks a bit weak as it is.
Zuki Build

Steady as she goes!

User avatar
hamer
Engaged 4wd low
Engaged 4wd low
Posts: 159
Joined: Mon Jul 23, 2012 8:06 pm
Location: bridgend

Re: ruf help :(

Post by hamer » Fri Feb 08, 2013 6:38 pm

thanks scotty
another half inch?
ye gna weld a peice make it triangle shape
used the bottom rear support spring as it was rite width
Attachments
2013-02-08 18.22.44.jpg
2013-02-08 18.22.44.jpg (1.53 MiB) Viewed 6585 times

User avatar
hamer
Engaged 4wd low
Engaged 4wd low
Posts: 159
Joined: Mon Jul 23, 2012 8:06 pm
Location: bridgend

Re: ruf help :(

Post by hamer » Fri Feb 08, 2013 7:21 pm

do i drill the rear spring eye back an inch??

User avatar
ScottieJ
The Boss
The Boss
Posts: 11618
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: ruf help :(

Post by ScottieJ » Sat Feb 09, 2013 11:01 am

I'd say another half inch would be spot on, I've never been sure about redrilling the spring hangers as there's not really a huge amount of material there.
Zuki Build

Steady as she goes!

User avatar
hamer
Engaged 4wd low
Engaged 4wd low
Posts: 159
Joined: Mon Jul 23, 2012 8:06 pm
Location: bridgend

Re: ruf help :(

Post by hamer » Sat Feb 09, 2013 6:01 pm

i drilled the rear eye back 3/4 inch it sat tidy naw
gnaa drill axle forward an inch as aint got much bulkhead clearance it rubs on full lock :(
my driver side is around an inch lower than passenger??
gonna change driver side spring also tommoz hopefully springs a bit nakered i have a few spares ther

User avatar
felstmiester
Engaged 4wd low
Engaged 4wd low
Posts: 165
Joined: Sat Dec 18, 2010 12:10 pm

Re: ruf help :(

Post by felstmiester » Mon Feb 11, 2013 7:48 am

This is how I done mine.
Attachments
image.jpg
image.jpg (87.04 KiB) Viewed 6503 times
1.5 ISUZU TD ENGINE. EXTERNAL ROLL CAGE. CUSTOM MADE FRONT & REAR BUMPERS. SAMMY AXLES. RASCAL REARS. RUF. WRX SEATS. FRONT & REAR WINCHES. SNORKEL. FRONT SPOTS & REAR FLOODS. TWIN BATTERIES. FULL WADING KIT. 8.5" WHEELS WITH GRIZZLY CLAWS. OH!!!! AND THE WIFE'S ROASTING TIN!!

User avatar
ScottieJ
The Boss
The Boss
Posts: 11618
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: ruf help :(

Post by ScottieJ » Mon Feb 11, 2013 8:40 am

Both of these really need some gussets in my opinion, they look a bit to weak for something that is supporting the heaviest end of a vehicle that will be used offroad.

I would really advise adding some gussets like these to avoid the risk of them failing or bending.
gussets.JPG
gussets.JPG (68.68 KiB) Viewed 6494 times
Zuki Build

Steady as she goes!

User avatar
hamer
Engaged 4wd low
Engaged 4wd low
Posts: 159
Joined: Mon Jul 23, 2012 8:06 pm
Location: bridgend

Re: ruf help :(

Post by hamer » Tue Feb 12, 2013 11:19 am

thanks guys i didnt put triangle bits in i put a peice in from front to top if you no wat i mean..
could weld gussets eiver side naw tho to strenphen it up but seems solid gave it loads of abuse on the weekend with no probs

Post Reply