Tramps Truck,
-
muddymesser
- Engaged 4wd low
- Posts: 189
- Joined: Mon Jun 29, 2009 9:10 pm
- Location: blackpool
Re: Tramps Truck,
nice
-
Tramp
- Suzuki, will you marry me?
- Posts: 2828
- Joined: Fri Jul 25, 2008 10:09 pm
- Location: Rotherham - South Yorkshire
Re: Tramps Truck,
......ordered 
- image.jpg (164.25 KiB) Viewed 5397 times
-
Tramp
- Suzuki, will you marry me?
- Posts: 2828
- Joined: Fri Jul 25, 2008 10:09 pm
- Location: Rotherham - South Yorkshire
Re: Tramps Truck,
I made a start fitting my bearing kit today, I had a few hours on it and got grease everywhere! I was chuffed to get the felt & rubber seal on without cutting it. Then I had to go to work, I did have one little issues though,
- My track rod end (well my ball joint), I was going to split the linkage so loosened the nut off the top unfortunately when it was far enough off I tapped it and the linkage started spitting, but now the entire track rod pivot spins when trying to undo the last threads on the nyloc nut, is there a bolt head under the rubber gator?
*edit* I gave the kingpin pivot a lick around with emery and it was fine, it slotted in easily like there was no problem!
- My track rod end (well my ball joint), I was going to split the linkage so loosened the nut off the top unfortunately when it was far enough off I tapped it and the linkage started spitting, but now the entire track rod pivot spins when trying to undo the last threads on the nyloc nut, is there a bolt head under the rubber gator?
*edit* I gave the kingpin pivot a lick around with emery and it was fine, it slotted in easily like there was no problem!
Last edited by Tramp on Mon May 19, 2014 4:32 am, edited 1 time in total.
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Tramps Truck,
Can normally just push it back up a little so the taper locks a bit to undo it and then tap it back down
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
Jordi
- Bow down before me
- Posts: 7534
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Tramps Truck,
Nice to see a bit more work being done. Can't wait to see this back on the road, always liked your truck for some reason bud.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
Tramp
- Suzuki, will you marry me?
- Posts: 2828
- Joined: Fri Jul 25, 2008 10:09 pm
- Location: Rotherham - South Yorkshire
Re: Tramps Truck,
Thanks 
I always liked my truck too!
I've had a busy evening..........
Hopefully it will be dry by the morning so it can be refitted,
I always liked my truck too! I've had a busy evening..........
- image.jpg (2.02 MiB) Viewed 5234 times
-
Tramp
- Suzuki, will you marry me?
- Posts: 2828
- Joined: Fri Jul 25, 2008 10:09 pm
- Location: Rotherham - South Yorkshire
Re: Tramps Truck,
Drivers side almost done
And one of the best bits about this rebuild kit......
Shiney bits!
And one of the best bits about this rebuild kit......
Shiney bits!
-
Tramp
- Suzuki, will you marry me?
- Posts: 2828
- Joined: Fri Jul 25, 2008 10:09 pm
- Location: Rotherham - South Yorkshire
Re: Tramps Truck,
Another fun day, I fitted my new bearing assy and king pin bearings on the passenger side, I fitted new brake hoses too but suffered a small issue
What are your thoughts on this? Drill it out and retapp it? Or do I need a new caliper? The drivers side bleed nipple is just as reluctant to be removed!
- image.jpg (1.66 MiB) Viewed 5155 times
Re: Tramps Truck,
Nice work! Will be awesome to see your Sk back on the road!
As for the nipple you could try a stud removal tool. http://www.ebay.co.uk/itm/110868152075
As for the nipple you could try a stud removal tool. http://www.ebay.co.uk/itm/110868152075
-
Tramp
- Suzuki, will you marry me?
- Posts: 2828
- Joined: Fri Jul 25, 2008 10:09 pm
- Location: Rotherham - South Yorkshire
Re: Tramps Truck,
Thanks I'll I've give it a go but I'm not hopeful it seemed pretty stuck! I could also do with another swivel hub seal bolt I had a full set but one has managed to get lost! If anyone has a spare kicking about? Its very annoying, what are my options if I cannot get the thread out? Do I need to buy a set if new calipers?