Dan_2k_uk's super shed thread!
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Dan_2k_uk's super shed thread!
So will it have additional cider storage?
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Dan_2k_uk's super shed thread!
Very productive day yesterday.
Finished cutting the last few roof panels and got it all totally fixed down.
Then got all the felt on. Sealant between all the joints and under / ontop of every nail.
Had to go grab an extra sheet of OSB in the Zook. Think 8'x4' is the full carrying capacity for an SJ
Luckily I had a mate round to help as the felting would have been a nightmare on my own.
I still need to add a few rows of tacks from front to back to make it extra secure but at least for now the roof is protected.
Finished cutting the last few roof panels and got it all totally fixed down.
Then got all the felt on. Sealant between all the joints and under / ontop of every nail.
Had to go grab an extra sheet of OSB in the Zook. Think 8'x4' is the full carrying capacity for an SJ
Luckily I had a mate round to help as the felting would have been a nightmare on my own.
I still need to add a few rows of tacks from front to back to make it extra secure but at least for now the roof is protected.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Dan_2k_uk's super shed thread!
Proper job!!!
Superb mate. Want!
Superb mate. Want!
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Dan_2k_uk's super shed thread!
Proper tidy job Dan.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Dan_2k_uk's super shed thread!
Started the cladding. Realised I wasn't going to get enough done to make it secure down the sides before tonight so turned my attention to the roof off and got it all tucked up and fixed under the frame and battened down the hatches for tonights storm.
Door and window blanked off with leftover roofing felt and the sides that are exposed above the fence blanked with scrap OSB to try keep the impact of the wind to a minimum.
Door and window blanked off with leftover roofing felt and the sides that are exposed above the fence blanked with scrap OSB to try keep the impact of the wind to a minimum.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
turbo-tom
- I spend far too much time on here
- Posts: 4478
- Joined: Fri Jun 25, 2010 9:29 pm
- Location: West Sussex
Re: Dan_2k_uk's super shed thread!
Looks very pro i must say! is that the only window your going to put in? presume your going to run power to it?
Tom 
Ford Fiesta ST
Ford Fiesta ST
-
dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: Dan_2k_uk's super shed thread!
Looks good Dan u have done a nice job on the shed
Tom we have a car battery in are shed and that powers one light in are shed tbh we never use it I only used it once when I was trying to get my bearing off my shaft as that's where the vice was
Tom we have a car battery in are shed and that powers one light in are shed tbh we never use it I only used it once when I was trying to get my bearing off my shaft as that's where the vice was
Last edited by dazerede on Sun Oct 27, 2013 8:19 pm, edited 1 time in total.
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Re: Dan_2k_uk's super shed thread!
That's looking good, I do hope that it comes to no harm.
2006 Jimny JLX+ 1.3 VVT
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Dan_2k_uk's super shed thread!
Yeah that's the only window.
Of course it will have power to it. Can't have a man cave without tunes and a welder.
Of course it will have power to it. Can't have a man cave without tunes and a welder.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.