Anton's build
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Anton's build
How much more to do before the MOT then?
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Anton's build
Get the reverse lights working
Wire up the rear number plate light
Fit/wire up the fog light and switch
Get new indicator bulbs (ordered)
Get new brake line clips and fit 'em
Find my stash of split pins and fit a couple to the castle nuts on the drag link/track rod ends
Get/make Rover rear caliper mounts.
Fit Rover rear calipers, bleed brakes.
Get flexi pipes for the rear calipers (Can't believe I
forgot that!)
Make rear brake pipe fittings and weld them to the
axle
Weld up and fit the exhaust
Should be do-able, if nothing else jumps out at me! I just hope I pass emissions...
Wire up the rear number plate light
Fit/wire up the fog light and switch
Get new indicator bulbs (ordered)
Get new brake line clips and fit 'em
Find my stash of split pins and fit a couple to the castle nuts on the drag link/track rod ends
Get/make Rover rear caliper mounts.
Fit Rover rear calipers, bleed brakes.
Get flexi pipes for the rear calipers (Can't believe I
forgot that!)
Make rear brake pipe fittings and weld them to the
axle
Weld up and fit the exhaust
Should be do-able, if nothing else jumps out at me! I just hope I pass emissions...
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Anton's build
2 weeks bud. Not bother.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
Edweird
- Suzuki, will you marry me?
- Posts: 2531
- Joined: Sat Jan 23, 2010 11:04 pm
- Location: Brigg, North Lincolnshire
Re: Anton's build
I had a chat with one of my friend's that works at a testing place the other day. He was saying that at his garage they got a car through the emissions by turning the 'idle' up to about 1800 revs.
There's three ways of doing things:
The right way,
The wrong way
And my way, which is like the wrong way but faster.
The right way,
The wrong way
And my way, which is like the wrong way but faster.
-
Edweird
- Suzuki, will you marry me?
- Posts: 2531
- Joined: Sat Jan 23, 2010 11:04 pm
- Location: Brigg, North Lincolnshire
Re: Anton's build
It's a carbon monoxide test and an unburnt fuel test. When I asked about it apparently all cars have to pass those.
There's three ways of doing things:
The right way,
The wrong way
And my way, which is like the wrong way but faster.
The right way,
The wrong way
And my way, which is like the wrong way but faster.
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Anton's build
Dont bother with welding brackets for the brake lines. Just bend a little L shaped bit of steel with 2 holes in it and secure the flexy and fixed line through it and bolt it to the old clip mount on the axle through the other hole.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Anton's build
Let's hope so!Jordi wrote:2 weeks bud. Not bother.
Yeah, HPOC Scottie told me about that one too! I may wind mine up to about 1200rpm before dropping 'er off, just in case.Edweird wrote:I had a chat with one of my friend's that works at a testing place the other day. He was saying that at his garage they got a car through the emissions by turning the 'idle' up to about 1800 revs.
I'll just make a "fork" and tack it on. It's 10 minutes work.dan_2k_uk wrote:Dont bother with welding brackets for the brake lines. Just bend a little L shaped bit of steel with 2 holes in it and secure the flexy and fixed line through it and bolt it to the old clip mount on the axle through the other hole.
The clip mount you speak of isn't on this axle anymore...
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map
Re: Anton's build
All SJs just need to meet 3.5% CO and 0.12% (HC)3 should be easy to meet as long as the engine is healthy.
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Anton's build
Made a couple of brake caliper templates today, out of ali checkerplate (not wood). First one didn't quite fit (caliper bolt holes 5mm too low). Second one fit perfectly:
Tomorrow's job: Make 2 of those out of 10mm steel plate, then make 13mm spacers, and find bolts that'll go through that lot!
Tomorrow's job: Make 2 of those out of 10mm steel plate, then make 13mm spacers, and find bolts that'll go through that lot!
Last edited by Anton on Sun Jul 16, 2017 6:35 pm, edited 1 time in total.
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map