edited! good luck matey, hope it all works well!Edweird wrote:Okay, I've put the overflow to run out of the drain hole behind the headlight, unblocked that vent and re-connected the fuel pump's return hose.
I'm going to take it out for a test drive.
Hopefully it'll run nice permanently now and not just for 12 hours.
Ed's wagon
Re: Ed's wagon
Re: Ed's wagon
How's the test drive go? it's been a while now so:
A: you're loving it and driven half way across the country?
B: you're broken down on the side of the road?
A: you're loving it and driven half way across the country?
B: you're broken down on the side of the road?
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Ed's wagon
Hes probably in the red stage about now!
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
ROBBIE
- I spend far too much time on here
- Posts: 4555
- Joined: Tue Sep 09, 2008 6:32 pm
- Location: Dorset or stuck
Re: Ed's wagon
^^ 
think im the blue 1
think im the blue 1Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Jimny 1.6 not as good as an SJ but still good
-
Edweird
- Suzuki, will you marry me?
- Posts: 2531
- Joined: Sat Jan 23, 2010 11:04 pm
- Location: Brigg, North Lincolnshire
Re: Ed's wagon
Sorry, yes, I am alive. I spent most of the day yesterday polluting the North Lincolnshire countryside.
The carb seems to work properly all the time now that I've changed those two hoses. The exhaust still smells a bit petrol-ish and idles a bit fast but it's smooth and it pulls.
The self returning choke is a nice feature.
The carb seems to work properly all the time now that I've changed those two hoses. The exhaust still smells a bit petrol-ish and idles a bit fast but it's smooth and it pulls.
The self returning choke is a nice feature.
There's three ways of doing things:
The right way,
The wrong way
And my way, which is like the wrong way but faster.
The right way,
The wrong way
And my way, which is like the wrong way but faster.
Re: Ed's wagon
Nice one! sounds like it needs a little tune up to lean out the mix and drop the idle then!
-
Edweird
- Suzuki, will you marry me?
- Posts: 2531
- Joined: Sat Jan 23, 2010 11:04 pm
- Location: Brigg, North Lincolnshire
Re: Ed's wagon
Yeah, I'm just trying to find out from Rodger what needle it had in it when he sent me it, 'cause I have an ADS needle in the box of bits he sent me, so I was wondering if it might have the wrong needle in.ScottieJ wrote:Nice one! sounds like it needs a little tune up to lean out the mix and drop the idle then!
There's three ways of doing things:
The right way,
The wrong way
And my way, which is like the wrong way but faster.
The right way,
The wrong way
And my way, which is like the wrong way but faster.
-
Edweird
- Suzuki, will you marry me?
- Posts: 2531
- Joined: Sat Jan 23, 2010 11:04 pm
- Location: Brigg, North Lincolnshire
Re: Ed's wagon
Okay, Rodger says that the SU's got an AAA needle in and I know that ADS is the recommended one. Rodger gave me a link to this website: www.mintylamb.co.uk/suneedle/
Here's a picture from that site with the four needles I've got on it, AAA, AAC, ABA and ADS.
I'm not 100% sure what it's telling me. Is higher up the graph richer or leaner?
Here's a picture from that site with the four needles I've got on it, AAA, AAC, ABA and ADS.
- SU needles.png (86.75 KiB) Viewed 7322 times
There's three ways of doing things:
The right way,
The wrong way
And my way, which is like the wrong way but faster.
The right way,
The wrong way
And my way, which is like the wrong way but faster.
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Ed's wagon
Step 1 is where it sits at low revs/tickover but when you open her up and the needle moves towards the higher numbers the needle is quite a bit thinner so I will be richer higher up in the rev range.
They are easy to change and quite cheap. I would just get the correct needle before fiddling any further.
Dan
They are easy to change and quite cheap. I would just get the correct needle before fiddling any further.
Dan
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.