Re: July 6th-7th Wiltshire by-way session
Posted: Wed May 22, 2013 6:44 pm
Taaaaaaaaar. Should be a laugh
I hope that my steering will be fixed till this time.
Suzuki Club UK
Home of all things Suzuki 4x4
https://suzukiclubuk.co.uk/forum/phpBB3/
July 6th-7th Wiltshire by-way session
https://suzukiclubuk.co.uk/forum/phpBB3/viewtopic.php?t=7532
Page 9 of 30
Re: July 6th-7th Wiltshire by-way session
Posted: Thu May 23, 2013 8:46 am
After yesterday's chat with Scottie I think I can join also
I hope that my steering will be fixed till this time.
I hope that my steering will be fixed till this time.
Re: July 6th-7th Wiltshire by-way session
Posted: Fri May 31, 2013 10:33 am
5 weeks! Although for me it may aswel be 3 as I've got a week of Standby and the week I get off after standby so should fly by.
Re: July 6th-7th Wiltshire by-way session
Posted: Fri May 31, 2013 11:03 am
My week of has flown by. Its friday already. Wih the exception of a badly cobbled together front end its ready to go again though 
Re: July 6th-7th Wiltshire by-way session
Posted: Fri May 31, 2013 10:34 pm
Just realised its in July. I thought it was next weekend 
.
.Re: July 6th-7th Wiltshire by-way session
Posted: Wed Jun 12, 2013 10:32 pm
Just over 3 weeks to go!!!!
I only have a bucket load of stuff still to do. I haven't been home since my week off, due home tomorrow but i have a real bad feeling.
I'm counting the days lads!!!
I only have a bucket load of stuff still to do. I haven't been home since my week off, due home tomorrow but i have a real bad feeling.
I'm counting the days lads!!!
Re: July 6th-7th Wiltshire by-way session
Posted: Thu Jun 13, 2013 11:36 am
I've got a lot to do, my axles have started to fall apart 
got at least one wheel bearing and a diff to sort but might as well just get my full float rear axle fitted with the ARB.
got at least one wheel bearing and a diff to sort but might as well just get my full float rear axle fitted with the ARB.Re: July 6th-7th Wiltshire by-way session
Posted: Thu Jun 13, 2013 4:40 pm
No disasters yet. LWB to collect tomorrow and if Vitmad is about some 15x10s to collect too.
I need to swap my front clip and possibly splash some paint about. Handbrake may need fiddling with for MOT.
Then back to "dismantling" the LWB.
I need to swap my front clip and possibly splash some paint about. Handbrake may need fiddling with for MOT.
Then back to "dismantling" the LWB.
Re: July 6th-7th Wiltshire by-way session
Posted: Thu Jun 13, 2013 9:39 pm
I've still got a few bits to put back together too... both axles... all bearings/seals... rear disc conversion (thanks ferris)... new diff... master cylinder... weld on new perches... transferbox mounts... etc etc
Hopefully will get stuff sorted out and a bit of a shakedown before the 6th/7th but got to get on with it!
Hopefully will get stuff sorted out and a bit of a shakedown before the 6th/7th but got to get on with it!
Re: July 6th-7th Wiltshire by-way session
Posted: Thu Jun 13, 2013 9:56 pm
Well I checked my wheel bearings today and they are fine, got a little slop in a kingpin and a warped disc though at least I've got a stack of spare discs 
started getting my full float axle sorted ready to go on, got some stuff to chop off it, extend the spring perches for 410 spacing, build up the diff and she'll be good to go.
at least I've got a stack of spare discs started getting my full float axle sorted ready to go on, got some stuff to chop off it, extend the spring perches for 410 spacing, build up the diff and she'll be good to go.