Jordis 1988 Samurai (Re)Build

Got an vehicle build underway? post up pictures and tell us all how its going!

Builds threads only please.
User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4553
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: Jordi's 1988 Samurai Build

Post by ROBBIE » Sun Jun 23, 2013 4:28 pm

Sound like the problem I had when I put the 31s on
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Jordi's 1988 Samurai Build

Post by Jordi » Sun Jun 23, 2013 4:41 pm

I thought is be ok. The 31s had loadsa room.

It'll be right
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4553
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: Jordi's 1988 Samurai Build

Post by ROBBIE » Sun Jun 23, 2013 5:27 pm

I chopped mine back 2inch and did a bit of a virtual lift on the bulkhead at the same time
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Jordi's 1988 Samurai Build

Post by Jordi » Sun Jun 23, 2013 6:21 pm

Yup. Its already had that.

Its only fouling on the bottom corner of the sills so i'm just gonna cut them at an angle. Should sort it / make it usable for wiltshire.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Jordi's 1988 Samurai Build

Post by Jordi » Sun Jun 23, 2013 11:08 pm

I miss it already! Roll on friday.

Feels a lot more solid driving it now, think the tyres may be over inflated.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: Jordi's 1988 Samurai Build

Post by turbo-tom » Sun Jun 23, 2013 11:10 pm

My 31's rub my bulkhead but i havent got virtual lift or the bulk head cut and welded back just each time i go out and rubs i bash it one with the club hammer im getting it closer and closer each time so its nearly perfect! :cowboy::
Tom :)

Ford Fiesta ST :D

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Jordi's 1988 Samurai Build

Post by Jordi » Sun Jun 23, 2013 11:13 pm

I had loads of room on 31s. The bulk head has been cut back.

I wont know till i get it off road how / where they catch. Find out soon enough.

If my Dads is up and running for next sunday he's on about taking them to pea farm for a pay n play.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Jordi's 1988 Samurai Build

Post by Jordi » Wed Jun 26, 2013 9:37 pm

I've just been flicking through all my photos on my phone. When i first painted the Zuk it looked quite good, reasonably well painted and put together.

It looks quite sad now. I must get the bodywork tidied up as soon as the oily bits are done after the MOT.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
suzukisteve
Suzuki Guru
Suzuki Guru
Posts: 1344
Joined: Sat Feb 04, 2012 10:07 am
Location: Christchurch, Dorset

Re: Jordi's 1988 Samurai Build

Post by suzukisteve » Wed Jun 26, 2013 9:41 pm

at least its stands out when its multi coloured jordi lol. Any ideas on what colour your gonna end up with mate?
pickle power!

User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: Jordi's 1988 Samurai Build

Post by turbo-tom » Wed Jun 26, 2013 9:42 pm

no zuki looks sad they just looked well loved and used!
Tom :)

Ford Fiesta ST :D

Post Reply