Tims SJ410 Build Project

Got an vehicle build underway? post up pictures and tell us all how its going!

Builds threads only please.
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Tims SJ410 Build Project

Post by Jordi » Thu Nov 21, 2013 10:17 pm

Tidy work bud!
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

User avatar
timwilks13
SCUK Website Padawan
SCUK Website Padawan
Posts: 1248
Joined: Sun Feb 03, 2013 5:55 am
Location: Scarborough, soon to be Poland

Re: Tims SJ410 Build Project

Post by timwilks13 » Thu Nov 21, 2013 11:25 pm

This evenings update, front end off, engine and box out. Replacement engine cleaned a bit, swapped the dizzy fly wheel, clutch, gear box and starter motor across, tomorrow I will do the inlet manifold and alternator and get it put back in, and hope it runs better than the one I've taken out to please mister mot man. He didn't like the fact that I was burning so much oil he didn't even fully complete the emissions test as the garage was full of black smoke!
I'll put pictures up in a sec as my tablet has decided it doesn't want to let me.
1986 SJ410 - Furry dice, new window winder.

10 kinds of people in this world, those who understand binary and those who dont.

if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.

User avatar
timwilks13
SCUK Website Padawan
SCUK Website Padawan
Posts: 1248
Joined: Sun Feb 03, 2013 5:55 am
Location: Scarborough, soon to be Poland

Re: Tims SJ410 Build Project

Post by timwilks13 » Fri Nov 22, 2013 8:44 am

Pictures as promised, not very exciting im afraid, but still, progress all the same!
Attachments
IMG_20131121_230338.jpg
IMG_20131121_230338.jpg (2.46 MiB) Viewed 4730 times
IMG_20131121_205336.jpg
IMG_20131121_205336.jpg (1.98 MiB) Viewed 4730 times
IMG_20131121_191801.jpg
IMG_20131121_191801.jpg (2.63 MiB) Viewed 4730 times
IMG_20131121_191746.jpg
IMG_20131121_191746.jpg (2.44 MiB) Viewed 4730 times
1986 SJ410 - Furry dice, new window winder.

10 kinds of people in this world, those who understand binary and those who dont.

if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.

User avatar
ScottieJ
The Boss
The Boss
Posts: 11620
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: Tims SJ410 Build Project

Post by ScottieJ » Fri Nov 22, 2013 12:43 pm

Looks like you have been having fun :doublethumbs:
Zuki Build

Steady as she goes!

User avatar
timwilks13
SCUK Website Padawan
SCUK Website Padawan
Posts: 1248
Joined: Sun Feb 03, 2013 5:55 am
Location: Scarborough, soon to be Poland

Re: Tims SJ410 Build Project

Post by timwilks13 » Fri Nov 29, 2013 4:33 pm

replacement engine is in, tonight ill get her wired up and running hopefully, fingers crossed it doesnt smoke like a tyre on fire like the last one!
1986 SJ410 - Furry dice, new window winder.

10 kinds of people in this world, those who understand binary and those who dont.

if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.

User avatar
Edweird
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2531
Joined: Sat Jan 23, 2010 11:04 pm
Location: Brigg, North Lincolnshire

Re: Tims SJ410 Build Project

Post by Edweird » Fri Nov 29, 2013 4:45 pm

Looks like we're going to have to arrange another off-road weekend so we can tune it up again.
There's three ways of doing things:

The right way,
The wrong way
And my way, which is like the wrong way but faster.

User avatar
timwilks13
SCUK Website Padawan
SCUK Website Padawan
Posts: 1248
Joined: Sun Feb 03, 2013 5:55 am
Location: Scarborough, soon to be Poland

Re: Tims SJ410 Build Project

Post by timwilks13 » Fri Nov 29, 2013 4:49 pm

Edweird wrote:Looks like we're going to have to arrange another off-road weekend so we can tune it up again.
because the carb was set up quite well i have swapped the whole manifold over with carb attached and everything, so if i can get the engine tuned like the last one, fingers crossed there wont be much more tuning needed!
1986 SJ410 - Furry dice, new window winder.

10 kinds of people in this world, those who understand binary and those who dont.

if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.

User avatar
twiss
SCUK Computer Wizard
SCUK Computer Wizard
Posts: 6110
Joined: Mon Nov 08, 2010 2:28 pm
Location: Birkirkara, Malta
Contact:

Re: Tims SJ410 Build Project

Post by twiss » Tue Dec 03, 2013 11:07 am

There may be slight variations in the tuning required with a different engine, but it shouldn't be too far off :)
Twiss

'93 Suzuki Samurai Sport 1.6 16v SU. Virtual lift, spring under, 31s
'93 Maruti Gypsy MG410

"If brute force doesn't fix your problem, you aren't using enough of it."

User avatar
timwilks13
SCUK Website Padawan
SCUK Website Padawan
Posts: 1248
Joined: Sun Feb 03, 2013 5:55 am
Location: Scarborough, soon to be Poland

Re: Tims SJ410 Build Project

Post by timwilks13 » Tue Dec 03, 2013 11:20 am

Yea im sure a bit of tinkering is required, however got another issue to sort first! Got the engine in the other night, wired up all the basics, starter motor, alternator etc and tried to start it to check it runs, got a click, a random spark or two and some smoke....not from the exhaust....somethings not quite right!
1986 SJ410 - Furry dice, new window winder.

10 kinds of people in this world, those who understand binary and those who dont.

if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.

User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7534
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: Tims SJ410 Build Project

Post by Jordi » Tue Dec 03, 2013 11:35 am

timwilks13 wrote:Yea im sure a bit of tinkering is required, however got another issue to sort first! Got the engine in the other night, wired up all the basics, starter motor, alternator etc and tried to start it to check it runs, got a click, a random spark or two and some smoke....not from the exhaust....somethings not quite right!
Check all your main electrical connections, particularly battery and starter. Sometimes if these are super tight you don't get a good enough current. Especially if they aren't earthed very well.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank

Post Reply