- 2013-07-07-209.jpg (1.49 MiB) Viewed 6066 times
Why Have They Done This
-
Famerbennie
- Engaged 4wd low
- Posts: 114
- Joined: Mon Apr 25, 2011 2:23 pm
- Location: Chelmsford
Why Have They Done This
Recently Done My SPOA Sammi Axle Conversion On My 410 But With The Astra Shocks Fitted They Were Bottoming out So Cut My Old 2" Lift Shackles Down By About 1" But Ever Since They Look Like This
Any Ideas Why???
-
dazerede
- Suzuki, will you marry me?
- Posts: 2141
- Joined: Fri Sep 30, 2011 10:23 pm
- Location: cornwall callington
Re: Why Have They Done This
Was it looking alright before u cut the shackels
Suzuki Sj 410 Jap Built
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
Recaro Seats Fitted
Landini Blue Colour
Full rollcage and winch bumper
1.6 8v vitara lump with su carb
4” calmini lift kit
235/75/15 insa turbo special tracks
99.9% Rust Free
BUILT NOT BOUGHT
-
Famerbennie
- Engaged 4wd low
- Posts: 114
- Joined: Mon Apr 25, 2011 2:23 pm
- Location: Chelmsford
Re: Why Have They Done This
yep they were fine before they got the chop:!:
Re: Why Have They Done This
Is it only on one side or both?
Did you cut the old perches off and weld them on spoa or get new perches and weld them on above the old ones?
Could you have welded the perch too far in on the axle? Can you measure up how far it is between the middle of each spring at the axle and post up the results?
Did you cut the old perches off and weld them on spoa or get new perches and weld them on above the old ones?
Could you have welded the perch too far in on the axle? Can you measure up how far it is between the middle of each spring at the axle and post up the results?
-
Famerbennie
- Engaged 4wd low
- Posts: 114
- Joined: Mon Apr 25, 2011 2:23 pm
- Location: Chelmsford
Re: Why Have They Done This
It's The Same All The Way Around The Car, The Saddles Are New Ones Welded On In The 410 Position On Top, And Were Abouts Did You Want The Measurements From ( Middle Of Spring To Back Plates?)
-
dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Why Have They Done This
He wants to know the distance between the perches so he can work out if the axle is out.Famerbennie wrote:It's The Same All The Way Around The Car, The Saddles Are New Ones Welded On In The 410 Position On Top, And Were Abouts Did You Want The Measurements From ( Middle Of Spring To Back Plates?)
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
-
Famerbennie
- Engaged 4wd low
- Posts: 114
- Joined: Mon Apr 25, 2011 2:23 pm
- Location: Chelmsford
Re: Why Have They Done This
After Closer Examination It Would Appear They Lean Because The Holes Don't Line Up! 
-
Jordi
- Bow down before me
- Posts: 7534
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Why Have They Done This
D'oh!!!
At least its an easy fix bud.
At least its an easy fix bud.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: Why Have They Done This
Famerbennie wrote:After Closer Examination It Would Appear They Lean Because The Holes Don't Line Up!
that was the next thing I was going to say, if I hold my phone so the shackles are vertical in the pic you can see it Easy thing to do.