Mikes Samurai build / use / fixing broken bits after abuse
- dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Mikes Samurai build updated 17/05/13 :)
Standard zook interior.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
- ROBBIE
- I spend far too much time on here
- Posts: 4555
- Joined: Tue Sep 09, 2008 6:32 pm
- Location: Dorset or stuck
Re: Mikes Samurai build updated 17/05/13 :)
Looks good as said bit dirty in there
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Jimny 1.6 not as good as an SJ but still good
- mike harris
- SCUK is my life
- Posts: 1828
- Joined: Sat Jan 08, 2011 8:30 pm
- Location: hascombe Surrey
Re: Mikes Samurai build updated 17/05/13 :)
Here we go lads
- Attachments
-
- image.jpg (1.12 MiB) Viewed 5333 times
-
- image.jpg (1.85 MiB) Viewed 5333 times
-
- image.jpg (1.83 MiB) Viewed 5333 times
- mike harris
- SCUK is my life
- Posts: 1828
- Joined: Sat Jan 08, 2011 8:30 pm
- Location: hascombe Surrey
Re: Mikes Samurai build updated 17/05/13 :)
My winch had a bow motor 2 fitted to make it faster and more torquey !! And loads of other little bits too, hopefully get it wired up this week one night.
So much to do and no time to do it !!
So much to do and no time to do it !!
- dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: Mikes Samurai build updated 17/05/13 :)
Thats a lotta winch
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Mikes Samurai build updated 17/05/13 :)
Might need sommit a bit better than a g clamp to fit it mike.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: Mikes Samurai build updated 17/05/13 :)
Gwyn lewis tray? Good bit of kit, nice bloke too
You bracing it back to the chassis?
Looks the nuts bud
Enjoy your 8274, they're great
You bracing it back to the chassis?
Looks the nuts bud
Enjoy your 8274, they're great
- mike harris
- SCUK is my life
- Posts: 1828
- Joined: Sat Jan 08, 2011 8:30 pm
- Location: hascombe Surrey
Re: Mikes Samurai build updated 17/05/13 :)
Yeh gwyn troff, troff is seem welded to the bumper top bottom and sides and plug welded through 8 holes 40mm diameter, then the bumper is welded to the chassis underneath to the tube and just in front of the steering box. And it's bolted with 10 m10 bolts, throughout the top, and through the standard bumper mounts. I don't think that will move, would stall the winch before that let go.
Yeh 8274 are pretty awesome, I have used them before winching mine out with mates trucks. Sould pull my sj along alrite.
Still more to do before I can play this weekend. Need to get cracking !! This is never ending !!!
Yeh 8274 are pretty awesome, I have used them before winching mine out with mates trucks. Sould pull my sj along alrite.
Still more to do before I can play this weekend. Need to get cracking !! This is never ending !!!
Re: Mikes Samurai build updated 17/05/13 :)
Fuck... that aint going anywhere haha
Yeah I run the same setup with bow 2 its spot on mate
Still bloody quick haha
Hope its all ready for the weekend bud
Yeah I run the same setup with bow 2 its spot on mate
Still bloody quick haha
Hope its all ready for the weekend bud
- mike harris
- SCUK is my life
- Posts: 1828
- Joined: Sat Jan 08, 2011 8:30 pm
- Location: hascombe Surrey
Re: Mikes Samurai build updated 17/05/13 :)
nearly there lol !!
got the axle breather on and the bumper properly painted last night, had a coolant pipe issue to which seemed to have made it past me !!
when I have finished work just need to do the winch and drill one hole and then its ready for playing !!
got the axle breather on and the bumper properly painted last night, had a coolant pipe issue to which seemed to have made it past me !!
when I have finished work just need to do the winch and drill one hole and then its ready for playing !!