HELP !!! Advice needed asap

Not covered by any of categories below, want a winch or need to buy some recovery gear then your question goes in here!

You will also find online parts catalogues, Service manuals and a other useful info here.
Post Reply
User avatar
dunnin21
Engaged 4wd low
Engaged 4wd low
Posts: 242
Joined: Thu Jan 26, 2012 8:19 pm
Location: Sunderland

HELP !!! Advice needed asap

Post by dunnin21 » Sun Jun 09, 2013 8:00 pm

I was wading today and submerged my sj. It cut out. I havnt re started it yet iv took the plugs out and I'm gona change oil. What else do I need to do before I try to start it. Iv got a 1600 spi engine

Thanks in advance
Top
User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: HELP !!! Advice needed asap

Post by turbo-tom » Sun Jun 09, 2013 8:06 pm

Try this fella! ;) sounds like a good day out! :lol:

http://www.suzukiclubuk.co.uk/diy/21-mi ... ned-engine
Tom :)

Ford Fiesta ST :D
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: HELP !!! Advice needed asap

Post by Jordi » Sun Jun 09, 2013 9:00 pm

Check all air intake for water ingestion. Take the plugs out and turn it over by hand.

Oil and filters as you said, check inside the dizzy cap.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
ScottieJ
The Boss
The Boss
Posts: 11620
Joined: Tue Apr 15, 2008 12:13 pm
Location: Chippenham, wiltshire

Re: HELP !!! Advice needed asap

Post by ScottieJ » Sun Jun 09, 2013 9:02 pm

If the ECU went underwater, make sure that is fully dried out before starting it up as well.
Zuki Build

Steady as she goes!
Top
User avatar
dunnin21
Engaged 4wd low
Engaged 4wd low
Posts: 242
Joined: Thu Jan 26, 2012 8:19 pm
Location: Sunderland

Re: HELP !!! Advice needed asap

Post by dunnin21 » Sun Jun 09, 2013 9:24 pm

Went up to headlining thanks for help guys
Top
User avatar
Jordi
Bow down before me
Bow down before me
Posts: 7535
Joined: Sun Nov 29, 2009 2:35 pm
Location: Darlington, Co. Durham

Re: HELP !!! Advice needed asap

Post by Jordi » Sun Jun 09, 2013 9:26 pm

Thats gonna take some drying out.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Top
User avatar
dunnin21
Engaged 4wd low
Engaged 4wd low
Posts: 242
Joined: Thu Jan 26, 2012 8:19 pm
Location: Sunderland

Re: HELP !!! Advice needed asap

Post by dunnin21 » Sun Jun 09, 2013 9:27 pm

Lol yeh tell me about it
Top
User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: HELP !!! Advice needed asap

Post by turbo-tom » Sun Jun 09, 2013 9:30 pm

Proper job of that mate! :lol:
Tom :)

Ford Fiesta ST :D
Top
User avatar
Ladaman
Suzuki Guru
Suzuki Guru
Posts: 1090
Joined: Thu Sep 08, 2011 10:56 pm
Location: Huddersfield, W. Yorkshire
Contact:
Contact Ladaman

Re: HELP !!! Advice needed asap

Post by Ladaman » Sun Jun 09, 2013 9:38 pm

:hahaha:

Yep that's certainly a bit damp!!
YouTube
Ignis Sport 1.5 16V; Jimny gearbox, 410 transfer box; 5.125:1 Vitara diffs; rear Lockright, Rob Storr full float rear axle, rear discs, YJ springs, virtual lift, 31" Grizzly Claws, beadlock rims, +50mm LR arches, LED rear lights, LED roof spots, bucket seats, Luke harnesses, internal cage
Top
User avatar
dunnin21
Engaged 4wd low
Engaged 4wd low
Posts: 242
Joined: Thu Jan 26, 2012 8:19 pm
Location: Sunderland

Re: HELP !!! Advice needed asap

Post by dunnin21 » Sun Jun 09, 2013 9:40 pm

Note to self, test snorkel before water
Top
Post Reply

Return to “General Troubleshooting, Offroad Gear, Welding & Fabrication”