Got an vehicle build underway? post up pictures and tell us all how its going!
Builds threads only please.
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Post
by Jordi » Mon May 27, 2013 10:32 pm
I'm starting this thread for Tim as we just swapped the doors over outside my house.
- image.jpg (2.76 MiB) Viewed 9759 times
- image.jpg (2.72 MiB) Viewed 9759 times
- image.jpg (2.92 MiB) Viewed 9759 times
They are very yellow against the red. Drivers side is a bit rusty along the bottom but a damn sight better than the old doors.
He also went away with a 1300 and a 5sp gearbox for a possible future engine swap. Still missing a few bits for the complete set up bit nothing that can't be easily sourced on here.
- image.jpg (2.77 MiB) Viewed 9759 times
Thanks again for collecting the alternator
Last edited by
Jordi on Mon Jul 01, 2013 10:34 pm, edited 1 time in total.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
turbo-tom
- I spend far too much time on here
- Posts: 4478
- Joined: Fri Jun 25, 2010 9:29 pm
- Location: West Sussex
Post
by turbo-tom » Mon May 27, 2013 11:00 pm
looking good! i love an old red 410 that looks like its had a hard life!
Tom
Ford Fiesta ST
-
OllieSJ
- ...
- Posts: 0
- Joined: Tue Feb 28, 2012 2:15 pm
Post
by OllieSJ » Mon May 27, 2013 11:02 pm
It looks like it shouldn't be on the road !
Sj410Q- Spacers, Bucket seats, Su carb , Mot and Tax
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Post
by Jordi » Mon May 27, 2013 11:04 pm
MOT till november i think he said. But it has had a hard life.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
timwilks13
- SCUK Website Padawan
- Posts: 1248
- Joined: Sun Feb 03, 2013 5:55 am
- Location: Scarborough, soon to be Poland
Post
by timwilks13 » Thu May 30, 2013 1:44 pm
As this is my build thread i should probably comment on it! It does look a little worse for wear but as Jordi says its pretty much solid rust wise, as in there is next to none. The doors were pretty much disintigrated, but sorted that with my new shiny ones! Windscreen frame is knackered but sorting a new one soon.
However the fun starts on sunday! If anyone is up and around scarborough way this sunday im taking my engine and gear box out to get ready to fit my new 1.3!
1986 SJ410 - Furry dice, new window winder.
10 kinds of people in this world, those who understand binary and those who dont.
if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.
-
timwilks13
- SCUK Website Padawan
- Posts: 1248
- Joined: Sun Feb 03, 2013 5:55 am
- Location: Scarborough, soon to be Poland
Post
by timwilks13 » Wed Jun 05, 2013 7:41 pm
Progress has been a little slower than expected as it took me the best part of a decade to get my front end off! But with a polite chat and a massive hammer it played ball! Progress so far...
-
Attachments
-
-
-
-
1986 SJ410 - Furry dice, new window winder.
10 kinds of people in this world, those who understand binary and those who dont.
if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Post
by Jordi » Wed Jun 05, 2013 7:46 pm
Getting there. At least it makes it nice and easy to get the engine out. When you put it back together use hex head bolts. It might be neccessary to drill some out completely and put a nut and bolt in.
Don't forget you have your "new" windscreen surround too!!!
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
timwilks13
- SCUK Website Padawan
- Posts: 1248
- Joined: Sun Feb 03, 2013 5:55 am
- Location: Scarborough, soon to be Poland
Post
by timwilks13 » Wed Jun 05, 2013 7:53 pm
i cannot wait to get that windscreen surround put on!!! gonna look so much better! i have cleared most of the holes to put new bolts all the way through, but bent one side of the front end in frustration getting it off so will all need a bit of a straighten and re spray before goin back together!
1986 SJ410 - Furry dice, new window winder.
10 kinds of people in this world, those who understand binary and those who dont.
if you can read this you're too close to the monitor, sit back and save your eyes!!
My build, formally Trotters build.
-
Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Post
by Jordi » Wed Jun 05, 2013 8:12 pm
Do we know if the gearbox will go in or if the mounts need modding yet?
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
turbo-tom
- I spend far too much time on here
- Posts: 4478
- Joined: Fri Jun 25, 2010 9:29 pm
- Location: West Sussex
Post
by turbo-tom » Wed Jun 05, 2013 9:37 pm
Looking good Tim. In your third picture down whats that metal plate in the footwell with the switches? In it looks intreeging lol
Tom
Ford Fiesta ST
