Fitting the springs on the exhaust help!!

Engine not running right? see if we can help you!
Post Reply
slaterfett
Got muddy boots
Got muddy boots
Posts: 15
Joined: Fri Aug 24, 2012 7:03 pm

Fitting the springs on the exhaust help!!

Post by slaterfett » Tue Mar 19, 2013 2:44 pm

Hi guys.

I'm in the process of refitting my exhaust. I've got to fit the exhaust to the mainfold but there are two springs which fits around the bolt then goes in to the mainfold.

How the hell do you compress these to get them to fit????

Cheers folks!
I'm a stinking thief don't buy parts off me!
Top
cookie
Got muddy boots
Got muddy boots
Posts: 14
Joined: Sun Feb 17, 2013 7:42 pm
Location: hemel hempstead
Contact:
Contact cookie

Re: Fitting the springs on the exhaust help!!

Post by cookie » Tue Mar 19, 2013 4:23 pm

normally the bolts are longer then the springs, and the spring compresses when you do the bolt up. could be different on an sj but sounds like you got the wrong bolts.
Four out of three people have difficulty with fractions
Top
User avatar
turbo-tom
I spend far too much time on here
I spend far too much time on here
Posts: 4478
Joined: Fri Jun 25, 2010 9:29 pm
Location: West Sussex

Re: Fitting the springs on the exhaust help!!

Post by turbo-tom » Tue Mar 19, 2013 5:16 pm

24inch ratchet extention bar and push the springs flippin' hard thats how I did mine ;)
Tom :)

Ford Fiesta ST :D
Top
User avatar
dan_2k_uk
I spend far too much time on here
I spend far too much time on here
Posts: 4924
Joined: Tue May 06, 2008 5:19 pm
Location: Swindon, Wiltshire

Re: Fitting the springs on the exhaust help!!

Post by dan_2k_uk » Tue Mar 19, 2013 5:20 pm

Mine were long enough and just bolted up.
Image
Janspeed manifold, LWB Vit vented discs and calipers

Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
Top
User avatar
ROBBIE
I spend far too much time on here
I spend far too much time on here
Posts: 4555
Joined: Tue Sep 09, 2008 6:32 pm
Location: Dorset or stuck

Re: Fitting the springs on the exhaust help!!

Post by ROBBIE » Tue Mar 19, 2013 6:02 pm

Throw the springs away :D
Sid James gone but never forgotten
Jimny 1.6 not as good as an SJ but still good
Top
User avatar
Darrell
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2989
Joined: Wed Feb 23, 2011 7:54 pm
Location: south oxfordshire
Contact:
Contact Darrell

Re: Fitting the springs on the exhaust help!!

Post by Darrell » Tue Mar 19, 2013 7:27 pm

Mine is fitted with the original bolts. You can start them with no spring compression and wind them in until they reach the flange. At this they also have the correct compression/tension.
Attachments
Exhaust manifold bolts.jpg
Exhaust manifold bolts.jpg (70.39 KiB) Viewed 5513 times
2005-GV 1600se, "Hell" What do I know!
Top
User avatar
Darrell
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2989
Joined: Wed Feb 23, 2011 7:54 pm
Location: south oxfordshire
Contact:
Contact Darrell

Re: Fitting the springs on the exhaust help!!

Post by Darrell » Tue Mar 19, 2013 7:35 pm

slaterfett wrote:Hi guys.

I'm in the process of refitting my exhaust. I've got to fit the exhaust to the mainfold but there are two springs which fits around the bolt then goes in to the mainfold.

How the hell do you compress these to get them to fit????

Cheers folks!
I guess you don't have the original bolts so I would use a socket and extension from under the vehicle.
You can put a loose nut or 2 into the socket so as to stop the bolt head from entering the socket too far.
2005-GV 1600se, "Hell" What do I know!
Top
Post Reply

Return to “Engine”