New to site. My build so far!
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: New to site. My build so far!
Yeah, i'm going that way. Got the engine and power steering in the garage. Just waiting to get manifolds modded to SU carb and Rocklobster built up.
Plenty of them around at the moment. Gotta shop about as prices vary wildly.
Jordi
Plenty of them around at the moment. Gotta shop about as prices vary wildly.
Jordi
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
- Got muddy boots
- Posts: 96
- Joined: Thu Jan 31, 2013 8:56 pm
- Location: cheltenham
Re: New to site. My build so far!
ye seen one on ebay for 495? what sort price do you rekon im looking all in? i can make mounts ect myself
Re: New to site. My build so far!
Personally for the hassle involved, I would go 1.5D Saxo/106 or Izuzu engine, the 1.5D can be made to fit the 1.3 box, and the izuzu engine is a very strong reliable engine but requires a manta gearbox.dannytrigger wrote:been reading up on a few engine swaps thinikng going g16a purly for easy option see how that perfoms then maybe chop in an ldv lump at a later date
I found the length of the ldv 400 box caused problems when fitting, although this can be overcome by having one UJ on the bogey prop, if understand what I mean.
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: New to site. My build so far!
I paid £60 for a SPI minus exhaust manifold, starter and alternator.
Prices vary most quotes for a complete engine i got were around the £300 mark which i found exceptionally steep. I don't think many of the lads on here paid over £150.
There aren't really any mounts to make for a 1600. I think it uses the original passenger side mount and the drivers side just needs redrilling.
Jordi
Prices vary most quotes for a complete engine i got were around the £300 mark which i found exceptionally steep. I don't think many of the lads on here paid over £150.
There aren't really any mounts to make for a 1600. I think it uses the original passenger side mount and the drivers side just needs redrilling.
Jordi
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
- Got muddy boots
- Posts: 96
- Joined: Thu Jan 31, 2013 8:56 pm
- Location: cheltenham
Re: New to site. My build so far!
wow seems there are lots of 1.5d saxo engines out there! is there any write ups on this conversion? would like to go diesal if not too much work as all this work and no play makes me :-(
-
- Got muddy boots
- Posts: 96
- Joined: Thu Jan 31, 2013 8:56 pm
- Location: cheltenham
Re: New to site. My build so far!
jordi is the spi much more work to fit?
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: New to site. My build so far!
Im gonna run it on a HIF44. So almost a straight swap. Few mods to mate it to the gearbox. Plumbing and wiring is almost identical.
This is the thread where i asked most of my questions.
http://forum.suzukiclubuk.co.uk/vi ... 13/t,6099/
Jordi
This is the thread where i asked most of my questions.
http://forum.suzukiclubuk.co.uk/vi ... 13/t,6099/
Jordi
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
-
- Got muddy boots
- Posts: 96
- Joined: Thu Jan 31, 2013 8:56 pm
- Location: cheltenham
Re: New to site. My build so far!
brilliant gona hunt down an engine. wgat fuel pump did you use in end?
- dan_2k_uk
- I spend far too much time on here
- Posts: 4924
- Joined: Tue May 06, 2008 5:19 pm
- Location: Swindon, Wiltshire
Re: New to site. My build so far!
He hasn't done it yet. Any low pressure pump will do if you are running a carb.
Janspeed manifold, LWB Vit vented discs and calipers
Build thread -- Build photos -- HLA-Artwork
Coming soon: YJs, Trussed axles, Full float rear.
- Jordi
- Bow down before me
- Posts: 7535
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: New to site. My build so far!
It's on the list Dan. I'm psyching up for the big SCUK parts tour this weekend. I've been onto the boss and told him "you are aware i must be home thursday" no guarantee he was listening.
Hotels are booked. Van is booked. Aproximate times at places are sorted. Money is sorted!
Shame i have no holidays left to fit it all, gonna be some long weekends. Gotta save the holidays for the big occassion and xmas now.
Jordi
Hotels are booked. Van is booked. Aproximate times at places are sorted. Money is sorted!
Shame i have no holidays left to fit it all, gonna be some long weekends. Gotta save the holidays for the big occassion and xmas now.
Jordi
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank