will this be ok on my vit 1.6 8 valve?

Nasher · Post by **Nasher** » Mon Jan 03, 2011 9:21 pm

http://cgi.ebay.co.uk/MG-Metro-Austin-M ... 4aa781a006

also will it fit a 1.3 engine ok? i have a su at the moment but only 1 1/2 inch model

Post by **ScottieJ** » Mon Jan 03, 2011 11:40 pm

Yep thats the Su you want for a 1.3 or 1.6

Nasher · Post by **Nasher** » Tue Jan 04, 2011 8:47 am

cheers scottie green laned my little suzuki yesterday and was a good laugh cheers

twiss · Post by **twiss** » Tue Jan 04, 2011 10:56 am

I would advise getting a converted manifold rather than an adapter

theres a guy on difflock called "rockwatt" who does them. there's also Rhino Ray in Brighton who does them

Nasher · Post by **Nasher** » Tue Jan 04, 2011 1:41 pm

i have a converted manifold off a vit on my 1.3 engine at the moment but puttin the 1.6 engine back in as the 1.3 is just not enough for the 31's on the road along with a new 5 speed box but just dont know what transfer to use as i have a few of each 410's and 413's what do you guys think will be best?

twiss · Post by **twiss** » Tue Jan 04, 2011 1:46 pm

I'd say 410... if you have a prop handbrake on the t-box, you could then convert to rear disc brakes

Either that or send them off and get a rocklobster made for you

Nasher · Post by **Nasher** » Tue Jan 04, 2011 2:36 pm

im keen for a rocklobster but im not that keen but after yesterday becoming a land rover 101 tow point the transfer started rattling and the 2nd gear sync is gone in my box but hey all good fun

Post by **ScottieJ** » Tue Jan 04, 2011 3:58 pm

a 410 for now and send a 413 and 410 to Rockwatt for a rocklobster! trust me you'll wonder why you never did it sooner!

if your swapping the SU and inlet from the 1.3 to the 1.6 all you need to do is swap the needle and spring in the SU

you want a BFM needle and a Red or Yellow spring If i remember correctly

twiss · Post by **twiss** » Tue Jan 04, 2011 4:36 pm

I find the yellow spring works best for my 1600, red for the 1300

Nasher · Post by **Nasher** » Tue Jan 04, 2011 4:50 pm

i only have a 1 1/2 inch carb not a 1 3/4 so if anyone has one of them they want to sell it will be great and where is best to get springs and bits from?

Suzuki Club UK

will this be ok on my vit 1.6 8 valve?

will this be ok on my vit 1.6 8 valve?

Re: will this be ok on my vit 1.6 8 valve?

Re: will this be ok on my vit 1.6 8 valve?

Re: will this be ok on my vit 1.6 8 valve?

Re: will this be ok on my vit 1.6 8 valve?

Re: will this be ok on my vit 1.6 8 valve?

Re: will this be ok on my vit 1.6 8 valve?

Re: will this be ok on my vit 1.6 8 valve?

Re: will this be ok on my vit 1.6 8 valve?

Re: will this be ok on my vit 1.6 8 valve?

test