Dip switch location

A place for all UK LJ owners to introduce themselves and for all LJ series tech and builds
Pishadeperro
Got muddy boots
Got muddy boots
Posts: 48
Joined: Sat Jan 07, 2017 6:29 pm

Dip switch location

Post by Pishadeperro » Mon May 29, 2017 4:46 pm

Daft question but need to know where the dip switch is..is it on the steering column combination switch?

User avatar
Darrell
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2988
Joined: Wed Feb 23, 2011 7:54 pm
Location: south oxfordshire
Contact:

Re: Dip switch location

Post by Darrell » Mon May 29, 2017 5:06 pm

The LJ owners manual I have says this...
Attachments
de.png
de.png (314.81 KiB) Viewed 9763 times
2005-GV 1600se, "Hell" What do I know!

User avatar
donkeychomp
I spend far too much time on here
I spend far too much time on here
Posts: 3582
Joined: Thu Aug 18, 2011 3:49 pm
Location: Shepperton, Middx

Re: Dip switch location

Post by donkeychomp » Mon May 29, 2017 9:18 pm

And that's where it is on my LJ :brows:
If it ticks over...leave it

Tonypp
Got muddy boots
Got muddy boots
Posts: 53
Joined: Sat Jan 25, 2014 5:02 pm

Re: Dip switch location

Post by Tonypp » Wed May 31, 2017 3:49 pm

Yes indicators and dip switch. Couldn't get mine to work, checked the wiring which was fine. The problem was down to dust and dirt. The switch was full of it. Pulled it apart and needed a tooth pick to pry the muck out. Cleaned and back together and I was a happy chappie.

Pishadeperro
Got muddy boots
Got muddy boots
Posts: 48
Joined: Sat Jan 07, 2017 6:29 pm

Re: Dip switch location

Post by Pishadeperro » Fri Jun 02, 2017 1:28 pm

my wiring has been hacked about, the steering column switch had been broken so the previous owners have wired various alternative switches and added them to the dashboard. I bought a replacement combination switch but the forward and back high low beam part is obviously broke on this one also....

Tonypp
Got muddy boots
Got muddy boots
Posts: 53
Joined: Sat Jan 25, 2014 5:02 pm

Re: Dip switch location

Post by Tonypp » Sat Jun 03, 2017 6:01 am

If you have a replacement switch from a a LJ there is not much to break. They are fairly robust. A couple that I have played were full of dirt. Another fault I found has been the solder joints had broken. Worth a look inside but be careful when you take apart--- there is a small ball bearing in the indicator part of the switch, lose that and game over as it locates the position for left and right.

Pishadeperro
Got muddy boots
Got muddy boots
Posts: 48
Joined: Sat Jan 07, 2017 6:29 pm

Re: Dip switch location

Post by Pishadeperro » Mon Jun 12, 2017 12:59 pm

can get all the indicators to work by pull the hazard switch but can@t get them to flash any other way, I think the replacement combination switch is no good so I'll have to re-fit the replacement three way switch the car came with...anyone any ideas how to connect this?

User avatar
Darrell
Suzuki, will you marry me?
Suzuki, will you marry me?
Posts: 2988
Joined: Wed Feb 23, 2011 7:54 pm
Location: south oxfordshire
Contact:

Re: Dip switch location

Post by Darrell » Mon Jun 12, 2017 6:39 pm

Any help..
Attachments
pg244lg.jpg
pg244lg.jpg (625.79 KiB) Viewed 9619 times
pg247.jpg
pg247.jpg (54.46 KiB) Viewed 9619 times
2005-GV 1600se, "Hell" What do I know!

Pishadeperro
Got muddy boots
Got muddy boots
Posts: 48
Joined: Sat Jan 07, 2017 6:29 pm

Re: Dip switch location

Post by Pishadeperro » Tue Jun 13, 2017 4:14 pm

many thanks.....I'll give it a go but the prognosis is not good!

Pishadeperro
Got muddy boots
Got muddy boots
Posts: 48
Joined: Sat Jan 07, 2017 6:29 pm

Re: Dip switch location

Post by Pishadeperro » Fri Jun 16, 2017 4:05 pm

Darrell wrote:The LJ owners manual I have says this...
How strange, just tried to fit a replacement combination switch bought off ebay and realised the indicators work the wrong way around, but I've just read what it says in the owners book extract, so for a RH drive car you'll press down for the right hand side and push up for the left...surely thats wrong????
I've had to link some of the cables out as I've spent all day trying to get the indicators to work at all, the hazards all worked and by linking the cables I could get the indicators to work, but having stripped the switch down to investigate I can't understand how they would work as the contacts don't match the point where they should. I've rectified it but I'm obviously missing something vital

Post Reply