Got an vehicle build underway? post up pictures and tell us all how its going!
Builds threads only please.
-
rundo
- Got muddy boots
- Posts: 52
- Joined: Sun Nov 09, 2014 7:59 pm
Post
by rundo » Tue Jan 27, 2015 10:47 am
kiwizook wrote:you should be able to get it off with a wire brush on a drill or dremel. I just starting using por15 too, it's really expensive, but probably the greatest paint in existence! it'l do the job just fine on ali, without the need for primer or topcoat, and it's rock hard and chip free!
Not available in Bosnia
I am in lookout for substitute, there are some converter and 3in1 paints around. Will post what I have decided. While searching really could not find anybody on forum sports this hubs started to think it was aftermarket part? Even other SJ419 still got Aisin as standard. If anyone knows, picture is above, no marks on it except LOCK and FREE and made in USA between studs? Hubs are OK, work well its just for my future reference...
-
rundo
- Got muddy boots
- Posts: 52
- Joined: Sun Nov 09, 2014 7:59 pm
Post
by rundo » Tue Apr 21, 2015 2:24 pm
These hubs are WARN 39198 like on american Tracker/Sidekick. I did what I have planned. Took them off, removed chipping paint, and sanded 800 then 1400 and alu polishing paste at the end. Did not go all the way with buffing though. Just to have decent shine. Will get stainless steel bolts later too
-
donkeychomp
- I spend far too much time on here
- Posts: 3583
- Joined: Thu Aug 18, 2011 3:49 pm
- Location: Shepperton, Middx
Post
by donkeychomp » Wed Apr 22, 2015 1:53 am
What on earth is holding that wheel on? Are they plastic bolt covers?
If it ticks over...leave it
-
rundo
- Got muddy boots
- Posts: 52
- Joined: Sun Nov 09, 2014 7:59 pm
Post
by rundo » Wed Apr 22, 2015 2:44 pm
Yes, plastic covers packed with grease to keep water off threads and nuts...
Last edited by
rundo on Thu Apr 30, 2015 12:51 pm, edited 1 time in total.
-
Rhinoman
- Suzuki Guru
- Posts: 1034
- Joined: Tue Mar 26, 2013 5:42 pm
- Location: Brinkworth
-
Contact:
Post
by Rhinoman » Thu Apr 23, 2015 7:05 pm
rundo wrote:These hubs are WARN 39198 like on american Tracker/Sidekick.
Yes that's correct, they were also fitted on later model Vitaras. I had them on my Vit from new until one broke, they have a plastic cam inside that is prone to breaking.
2006 Jimny JLX+ 1.3 VVT
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
-
rundo
- Got muddy boots
- Posts: 52
- Joined: Sun Nov 09, 2014 7:59 pm
Post
by rundo » Mon Apr 27, 2015 2:36 pm
Rhinoman wrote:rundo wrote:These hubs are WARN 39198 like on american Tracker/Sidekick.
Yes that's correct, they were also fitted on later model Vitaras. I had them on my Vit from new until one broke, they have a plastic cam inside that is prone to breaking.
Right, dont like plastic inside either... are they interchangeable with standard Aisins?
-
Rhinoman
- Suzuki Guru
- Posts: 1034
- Joined: Tue Mar 26, 2013 5:42 pm
- Location: Brinkworth
-
Contact:
Post
by Rhinoman » Mon Apr 27, 2015 2:52 pm
Yes, there is no difference in bolt spacing or spline size.
2006 Jimny JLX+ 1.3 VVT
2000 Vitara 4u2 - Calmini 3+3, 33" MTs, 5:83 R&Ps, winch bumper, remapped ECU.
1986 Suzuki SJ413K - G16 conversion
1984 Suzuki SJ410 - Blitz
-
rundo
- Got muddy boots
- Posts: 52
- Joined: Sun Nov 09, 2014 7:59 pm
Post
by rundo » Thu Jun 18, 2015 8:59 am
Sun up - top down!
