Tramps Truck,
-
Tramp
- Suzuki, will you marry me?
- Posts: 2828
- Joined: Fri Jul 25, 2008 10:09 pm
- Location: Rotherham - South Yorkshire
Re: Tramps Truck,
It's started... Good by sill
I've got a couple of mates coming around later to give me a hand welding my box section in,
I've got a couple of mates coming around later to give me a hand welding my box section in,
Last edited by Tramp on Tue Jan 20, 2015 4:25 pm, edited 1 time in total.
Re: Tramps Truck,
Looking good Luke, only a matter of time before it's back on the road!
2002 Jimny O2 Ragtop
Safari Snorkel, Freewheeling Hub Conversion
Diff Breathers, G/Box and T/Box Breathers, 2in Suspension Lift
HD Recovery Points and Winch Plate
Kuhmo KL71 MT / Goodyear Wrangler AT
Wessex 4X4 Reponse - WE411
wessex4x4response.org.uk
-
Tramp
- Suzuki, will you marry me?
- Posts: 2828
- Joined: Fri Jul 25, 2008 10:09 pm
- Location: Rotherham - South Yorkshire
Re: Tramps Truck,
One sill in place, welded along the front, and tacked at the back, thanks to my mate Ian who did all the welding and my mate lee who did some grinding,
Last edited by Tramp on Tue Jan 20, 2015 4:27 pm, edited 1 time in total.
-
Anton
- I spend far too much time on here
- Posts: 3859
- Joined: Tue Jan 12, 2010 12:12 pm
- Location: London
Re: Tramps Truck,
Nice and tidy, that looks like it will last at least a decade! I love a well looked after zuk.
1985 SJ413VX (SJ50V) with SPOA, rear disc brakes, 31x10.5R15 Kaiman Malatesta tyres, an MOT and a lot left to do!
My: Build thread ● To-do list ● Pay and Play map
My: Build thread ● To-do list ● Pay and Play map
-
Tramp
- Suzuki, will you marry me?
- Posts: 2828
- Joined: Fri Jul 25, 2008 10:09 pm
- Location: Rotherham - South Yorkshire
Re: Tramps Truck,
Still working on the drivers side,
It was a nightmare around the footwell, damn tin worm! I still have to patch the rear flared arch mount, and replace part of the rear arch which had corroded out. I'll have another look tomorrow at the footwell and see if I'm happy with it, I think there are a few little holes that need either filling or a May put another piece of steel over the top,
It was a nightmare around the footwell, damn tin worm! I still have to patch the rear flared arch mount, and replace part of the rear arch which had corroded out. I'll have another look tomorrow at the footwell and see if I'm happy with it, I think there are a few little holes that need either filling or a May put another piece of steel over the top,
Last edited by Tramp on Tue Jan 20, 2015 4:28 pm, edited 1 time in total.
-
Jordi
- Bow down before me
- Posts: 7534
- Joined: Sun Nov 29, 2009 2:35 pm
- Location: Darlington, Co. Durham
Re: Tramps Truck,
Looking spot on Luke. While your doing major work might aswell cut the rot out the footwell and make new panels.
1988 Samurai - Truck Cab & Tray Back - 1.6 8v & HIF44 - Snorkel - Stack Exhaust - PAS, YJs & 33s - Trussed, Gusseted & Pumpkin Capped Axles - 4.3 R&Ps - 4.16 T/Box - Rear Air Locker - Full Float Back Axle & Discs - RCV Front Shafts - X-Eng Handbrake - Custom Fuel Tank
Re: Tramps Truck,
Always cut out and replace. Otherwise it will just rot out between the old and new panel.