Hi
Does anybody know where i can buy the seal that goes behind the flange on the rear diff on my samurai? Some long grass got pulled into it last year and it has leaked since.
Thankyou - Austin
Search found 15 matches
- Thu Apr 30, 2020 10:48 pm
- Forum: SJ series Transmission, Axles, Brakes, wheels and tyres.
- Topic: Diff flange seal
- Replies: 1
- Views: 2711
- Fri Nov 22, 2019 7:15 pm
- Forum: Engine
- Topic: High startup idle
- Replies: 2
- Views: 3464
Re: High startup idle
Thankyou, i may need to at some point. Iv stuck a fuse in the fault code slot and it there are no fault codes. It only does it from startup, when it has got warm and you restart the engine, it idles perfectly
- Sun Nov 17, 2019 9:58 pm
- Forum: Engine
- Topic: High startup idle
- Replies: 2
- Views: 3464
High startup idle
When starting my 1995 EFI samurai from cold, it revs up and idles at close to 3000rpm at startup and wont drop untill the engines hot.
Any ideas on how to adjust this as i dont think its normal.
Thankyou
Any ideas on how to adjust this as i dont think its normal.
Thankyou
- Wed Aug 28, 2019 9:19 am
- Forum: SJ series Transmission, Axles, Brakes, wheels and tyres.
- Topic: Gearbox output shaft seal
- Replies: 2
- Views: 3472
Re: Gearbox output shaft seal
Ok Thankyou, hopefully that will fix the issue!
- Tue Aug 27, 2019 12:04 am
- Forum: SJ series Transmission, Axles, Brakes, wheels and tyres.
- Topic: Gearbox output shaft seal
- Replies: 2
- Views: 3472
Gearbox output shaft seal
My SJ has developed a oil leak around the output shaft of the gearbox, on closer inspection there seems to be slight play in the output shaft which makes me think there is a bearing gone?
How could this be fixed? Is it just a push in oil seal? How do i change the bearing in the end?
Thank you
How could this be fixed? Is it just a push in oil seal? How do i change the bearing in the end?
Thank you
- Mon Feb 18, 2019 11:39 pm
- Forum: Electrical
- Topic: Interior light wiring
- Replies: 6
- Views: 5909
Re: Interior light wiring
Thanks for your help, i finally fixed it earlier, turns out at the top of the pillar the wiring had been bodged meaning that the wires were the wrong way round. Swapped them around and now the light works fine
- Sat Feb 16, 2019 3:46 pm
- Forum: Electrical
- Topic: Interior light wiring
- Replies: 6
- Views: 5909
Re: Interior light wiring
I still couldnt get it to work manually so i ran a wire from the negitive terminal of the battery to the manual part of the interior light and it still didnt work. I am not sure what to do next, yet it works when the door is open.
- Fri Feb 15, 2019 4:35 pm
- Forum: Electrical
- Topic: Interior light wiring
- Replies: 6
- Views: 5909
Re: Interior light wiring
Thanks very much, i done as you said today and found that the wires had corroded and broken. I rewired the section along the sill and now have 12v to the interior light. Next problem is that it only works when the drivers door is open. The wiring for the passenger door switch is missing. Any idea wh...
- Thu Feb 14, 2019 9:23 pm
- Forum: Electrical
- Topic: Interior light wiring
- Replies: 6
- Views: 5909
Interior light wiring
The interior light has never worked on my samurai, all wiring at the light end is connected up however when i use a multimeter it shows no output meaning that the wiring is broken, any ideas where the wires run so i can try and find the problem? Wiring diagrams dont actually show where the wires are...
- Sun Feb 03, 2019 8:41 pm
- Forum: Electrical
- Topic: Temp sender reading too high
- Replies: 13
- Views: 13453
Re: Temp sender reading too high
Yeah i think thats the problem, i have a spanish one